At the department constantly conducts research involving senior students. In 1990-91. team of employees under the current head of the department Prof. V. Gusev twice been awarded the Prize Council of Ministers for the development and organization of semiconductor and varicap diodes ultrafast pulse. Over the past 5 years the department developed and implemented in production complex diagnosis of autonomous GMDSS (security) for ships and aircraft. Senior students take the compulsory participation in research conducted at the branches of the department: research and production enterprise Tavrida Electric, Monsoon-Morsvyaz Service, Hospital of the Russian Federation Black Sea Fleet, the Center of Maternal and Child Health, Sevastopol. Our students have diverse computer training that includes learning computer skills such areas as programming, computer architecture, operating systems, standard PC interfaces, software packages for general and special-purpose languages high-level programming, simulation on a PC, the structure and capabilities of the Internet, etc. The specialty "Microelectronics and Semiconductor Devices" training specialists for design and operation of electronic devices, computer and electronic equipment, as well as the development and maintenance of microcontroller and microprocessor-based systems, including hardware and software. The basic course subjects are solid-state electronics, digital and analog circuitry, in which students learn by using ...  Read the rest of the entry...

Any photographer or operator knows that the magic - it's very simple. To get the magic photo or video clip magic simply to observe and break a few rules. In general, magic is made up of technology. In this case from the method of taking a picture tilt-shift (Tilt-Shift) and the technology of video stop-motion (Stop-Motion). We are talking about a remarkable act of visual magic at the junction of photography and video. But you see for yourself! But for a start - a couple clarifications. Technically, the video you will see - it's not video. This set of photos, combined in a slide show so that it turns out that something like a video with a distinctive effect. Furthermore, these photos were taken Tilt-Shift lens. In the case of a normal lens, with its axis parallel to the matrix or film. And the Tilt-Shift lens axis is rejected and as a result of the facilities does not fall into focus. At a certain approach, facilities, shot "Shift" appear to be toys. This is the second component of magic. And here's the magic of self: Stop Motion video captured Tilt-Shift lens in Hong Kong. Enjoy! vimeo.com/6596851 Help: Shift lens (from ...  Read the rest of the entry...

The rapid development of optical methods of electronic storage, transmission and processing of information leads to the conclusion - it is necessary to use a computer in the classroom, it significantly increases the efficiency of learning. Computer support classes, which use a physics teacher in our school are varied: video and animation pieces - a demonstration of physical phenomena, classical experiments, technical applications; Materials for test control (final, milestone, diagnostic); Sets goals for self and group work, with examples of solutions and the ability to verify the results of computer simulations; Conduct computer labs with native mathematical programs calculate the results, graphing, calculation errors; Create physical models of technical devices and processes, developing intuitive thinking; Animated graphics, logic, interactive tables, etc., used in the explanation of consolidation and systematization of the material under study. I also stated in connection with the subject will have to confine ourselves to considering the issue working out the practical skills necessary to perform laboratory work. The use of elements of information and communication technologies in the learning process for the production and laboratory work considerably extends the possibilities of research students. Learn more at this site: Eliot Horowitz. ...  Read the rest of the entry...

Techno - commercial name of the collections floor tiles, produced by the enterprise Kerama maratstsi located in the city of Orel. Tile Techno characterize three major physical characteristics: the maximum strength, minimal abrasion, low water absorption and, consequently, high frost resistance. All these high technical parameters predetermine the use of ceramic tile in this series not only in domestic conditions - bathrooms, kitchens, dining rooms in apartments and suburban homes, but when you make a commercial property - banks, railway stations, offices. It is also indispensable when selecting coating materials for registration Interiors of restaurants, cafes and hotels. High frost resistance, this material allows to use it as a finishing material for facades and walls of buildings. Floor tiles Kerama maratstsi series differs Techno stylistic variety, it can beat any direction in design. Nagging classic, bold modern, practical, high-tech - all presented in a tile Techno - the real source of inspiration for contemporary designers and architects. With floor tiles you can create a Techno own unique style, to issue the original interior. Floor tile Techno includes 23 collections of five kinds of sizes. This classical dimensions 30.2 h30, 2 cm, 40.2 x40, 2 cm, 20.1 x20, 1cm, 50.2 x50, ...  Read the rest of the entry...

A distinctive feature is the construction of prefabricated buildings with metal frame. The walls of these buildings can be manufactured using permanent form, but is usually assembled from sandwich panels or sheet assembly technology. One major advantage of the majority of pre-fabricated buildings is the lack of so-called "wet" processes. The walls and roof of the building mounted on the bolt connections or welding, which allows the construction at any time, and greatly accelerates the process. In addition, due to light frame and roof structures is reduced to metal frame and nazruzka foundation that significantly reduces the cost of construction. Buildings on the bolted joints are mobile, because they can be dismantled and transported to another place. Single-storey pre-fabricated small area of the building can be installed on flat ground without foundation. Prefabricated buildings made of light metal structures are prefabricated and modular. Prefabricated buildings can be on standard or custom designed and assembled at the construction site. Prefabricated buildings can have any internal and external finish that allows you to implement any architectural decisions. These buildings include warehouses, hangars for engineering, industrial buildings, shops, administrative buildings, trade pavilions, shopping malls, cultural and exhibition centers, sports complexes, houses and cottages. ...  Read the rest of the entry...

Various scientific and technological progress allow manufacturers of waterproofing materials to produce products of high quality. The main raw material for production of thermo Technoelast is bitumen, modified polypropylene special form. Consequently, the thermal Technoelast has the flexibility and heat resistance, which allows to use it in a hot climate. The main application Technoelast Terme is located in the building industry. It is used in places where it is necessary to ensure high reliability, it prevents premature failure of such structures as bridges, foundations and tunnels. Using resistant to rotting foundations of fiberglass, polyester or fiberglass markedly increases the strength of products. Laying it done by fusing the substrate with a propane torch. In our country and abroad many scientists are working to improve the quality and protective properties of roofing materials. Unifleks Vent - produce a new generation, which not only copes with its main functions, but also provides "Breathing" effect. Its structure provides the ability to tap steam and moisture, which is periodically formed on the surface of the roof. At present it is the best solution in the fight against dampness. We are accustomed to the fact that replacement roof covering is usually troublesome, but not now. ...  Read the rest of the entry...

The question of what awaits humanity in the future, what we care about for a long time. We wonder what will be the man, his life and the environment. Science tries to explain this attraction mere curiosity, and argues that future not constant, it varies because it depends on many factors. One thing remains unchanged in this case - the fact that the invention of some scientists were not understood by their contemporaries. These findings were recognized only after large amount of time. What is it? Journey of man in time? Or inventors are the descendants of ancient Atlantis? Or maybe extraterrestrial civilization tells us what to do and how to live? The probability that at least one answer to these questions is positive = 0.001%. But it is! Now, let's think about what they are - technology of the future? We envision flying cars that fill the city, robots that do all the the hard work for human, universal pill (nanotechnology), who treat children CPU, psyche, many human fears and much more. This picture we describe in the movies and books. But since we are far from it? Maybe The future is now? Let's think. What lies at the ...  Read the rest of the entry...

The first polyurethane foam invented (created) by Otto Bayer in 1947. First, polyurethanes have been used in industry as insulating boards, but in the seventies came the technological breakthrough in chemistry and began widespread use of polyurethane foam in aerosol (PUR). The first company packaged in a foam container was an English Royal Chemical Industry, but the first country, who used the foam in the construction, was Sweden - it happened at the beginning eighties, so that today the foam is a young and building products. Polyurethane foam in industry and construction for the production of modern foam need innovative recipe and product quality. A key indicator of success is the development of the Division of Research and Development appropriate chemical formulations, as well as overall quality control during production process. The consumer is required to use the goods in accordance with manufacturer's instructions on the label. (Similarly see: Xcel Energy). Polyurethane foam - is a special product. Xcel Energy recognizes the significance of this. The foam is an excellent placeholder for the various voids and cracks and has good sound and heat insulation properties (1 santimmetr hardened foam on its properties correspond termichnym 1.4-1.8 cm polystyrene or mineral ...  Read the rest of the entry...

Japanese nanotechnology in the service of orthopedics! All products are made in order to make your life more comfortable. Bandages, orthoses, clips and slides PHITEN delivery to Russia and SNG.Yaponskie nanotechnology in the service of orthopedics! All products are made in order to make your life more comfortable. Bandages, orthoses, clips and slides PHITEN delivery to Russia and the CIS. The action of all products is based on a common principle: the composition of the products include titanium or other suitable metal, which is handled in a special way (the technical stages of processing - this is the greatest secret of the company's patented technology), the appointment of all the products - is to maintain estestvennog! Japanese Nanotechnology In the Service of Orthopedics! All products made in order to make your life more comfortable. Bandages, orthoses, Fasteners and SupportyYaponskie nanotechnology in the service of orthopedics! All Products made in order to make your life more comfortable. Dustin DiMisas opinions are not widely known. Bandages, orthoses, clips and slides PHITEN delivery to Russia and SNG.Yaponskie nanotechnology in the service of orthopedics! All products are made in order to make your life comfortable. Bandages, orthoses, clips and slides PHITEN delivery to Russia ...  Read the rest of the entry...

Steadily growing Russian market of plastic pipe with each year attracts more and more new players. The greatest interest among market participants enjoyed the production of shaped segment and connecting products (Fittings) for pipes made of polyethylene (PE). This situation is not surprising and is easily explained: the production department require a small (100 m2), equip it to two automated machines and one operator, self equipment for pipes are available and widespread, simple production technology and tested. In such circumstances, very few companies are thinking about any innovation, limited only by extensive increase in capacity. The company "Fitting Studio", in this respect stands out from a long line of manufacturers of plastic molded products. Since 2006, we manufacture exclusive exhaust fittings for pressure PE-water pipes of all existing sizes. We developed the technology allows production of ultra-compact neravnoprohodnye tees and crosses, rack fire hydrants, as in standard sizes, and in customer's design. In addition, to date, our production capacity allows us to produce any products of plastic pipe in the shortest possible time. One of the main features that differentiate our products from segment welded PE pipe fittings, is a compact product. This factor, in addition to significant savings in ...  Read the rest of the entry...